← Back to Articles
Create table-based VOD VEs
Last Updated: June 30, 2026
  • Run these commands to create VEs for Table-based VOD (the following values are examples):

    configure video virtual-edge <0-7> port-map type (table8x8map | session | table10x6map) (no)

    table8x8map - 8x8 port map for Table-based VOD

    session - Port-map for Session-based VOD

    table10x6map - 10x6 port map for Table-based VOD

    NOTE: The default value is table8x8map, which is that required for Table-based VOD. Therefore, you need not execute this command if the UDP port map type has never been changed.

    configure video virtual-edge 0 data-interface loopback 1 input-port 1

    configure video virtual-edge 0 blocked-udp-port 500 1000 ipv4-address 10.10.10.10

    NOTE: The command, for blocking UDP ports, is optional.

    configure video virtual-edge 1 name Virtual_Edge_One

    configure video virtual-edge 1 data-interface loopback 4 input-port 1

    configure video virtual-edge 2 name Virtual_Edge_Two

    configure video virtual-edge 2 data-interface loopback 8 input-port 1

    configure video virtual-edge 3 name Virtual_Edge_Three

    configure video virtual-edge 3 data-interface loopback 12 input-port 1

    configure video virtual-edge * erm-srv-discovery 1

    configure video virtual-edge 0 erm-srv-discovery source-interface loopback 3

    configure video virtual-edge 0 erm-srv-discovery component-name cm-0

    configure video virtual-edge 0 interface ethernet 6/0 loopback 1 bandwidth 1000 or configure video virtual-edge 0 interface link-aggregate 0 loopback 1 bandwidth 3000

    NOTE: The bandwidth range is 0–10000 Mbps for an Ethernet port or 0–80000 Mbps for a LAG, where aggregate assigned bandwidth of all VEs cannot exceed the maximum bandwidth capacity of the Ethernet or LAG interface. Entering 0 gives ERM control of all bandwidth on the Ethernet/LAG interface.

    configure video virtual-edge 0 interface ethernet 7/0 loopback 1 bandwidth 1000 or configure video virtual-edge 0 interface link-aggregate 1 loopback 1 bandwidth 3000

    configure video virtual-edge 1 erm-srv-discovery source-interface loopback 5

    configure video virtual-edge 1 erm-srv-discovery component-name cm-1

    configure video virtual-edge 1 interface ethernet 6/1 loopback 4 bandwidth 1000

    configure video virtual-edge 1 interface ethernet 7/1 loopback 4 bandwidth 1000

    configure video virtual-edge 2 erm-srv-discovery source-interface loopback 9

    configure video virtual-edge 2 erm-srv-discovery component-name cm-2

    configure video virtual-edge 2 interface ethernet 6/2 loopback 8 bandwidth 1000

    configure video virtual-edge 2 interface ethernet 7/2 loopback 8 bandwidth 1000

    configure video virtual-edge 3 erm-srv-discovery source-interface loopback 13

    configure video virtual-edge 3 erm-srv-discovery component-name cm-3

    configure video virtual-edge 3 interface ethernet 6/4 loopback 12 bandwidth 1000

    configure video virtual-edge 3 interface ethernet 7/5 loopback 12 bandwidth 1000

    configure video virtual-edge * streaming-zone 0

    configure video virtual-edge * erm-srv-discovery enable

    configure video virtual-edge 0 shutdown no

    configure video virtual-edge 1 shutdown no

    configure video virtual-edge 2 shutdown no

    configure video virtual-edge 3 shutdown no