mpsNationalControlConfig

mpsNationalControlDetunneling

Determines whether the detunneling will be PID-based or ser- vice-based

mpsNationalControlEmmProvId

Active when in secondary or primary national control modes

mpsNationalControlInputPort

The Port number of the input card from which the MPS should detunnel the National Control stream when the MPS is configured as the primary MPS

mpsNationalControlInputSlot

The slot number of the input card from which the MPS should detunnel the National Control stream when the MPS is configured as the primary MPS

mpsNationalControlManagerState

The state of the MPS System Controller SW module known as the National Control Manager

mpsNationalControlMulticastMac

The multicast MAC address for the detunneled National Control stream for an MPS that is using Ethernet

mpsNationalControlPacketCounter

The number of UDP packets processed by National Control

mpsNationalControlPid

PID number to detunnel

mpsNationalControlRestartCounter

The number of times that the National Control process has restarted

mpsNationalControlServiceNum

Service number to use when deriving the ISO PID value for the National Control stream

mpsNationalControlStreamPres

Indicates whether the National Control stream is present in the MPS

mpsNationalControlUdpPort

The Ethernet UDP port for the detunneled National Control stream for an MPS that is using Ethernet

mpsSysAlarmBaseAcpUnitAddressChange

Set to 'warning' when a change in the MPS Base ACP Unit Address is detected at boot

mpsSysAlarmCommandsInError

Not implemented

mpsSysAlarmCommandTableNearFull

Set to 'warning' when the LOAD MPS Command Table is >= 90% full

mpsSysAlarmConfigurationFailure

Set when an error occurs in the configuration process

mpsSysAlarmDcVoltageFault

Set to 'critical' when there is a DC voltage fault

mpsSysAlarmFanFault

Set to 'major' when a fan is not functioning properly

mpsSysAlarmFatalSIFerror

Set to 'critical' when an error occurs in SIF communications that prevents further use of the SIF

mpsSysAlarmInputFailure

Set to 'critical' when any input (either physical input to the MPS or an input to a functional module from the backplane) that should be active (not disabled) has a failure

mpsSysAlarmInsertionRate

Set to 'warning' when the MPS cannot insert messages at specified insertion rates

mpsSysAlarmMissingSourceTime

Set to 'warning' when the source of the MPS system time is missing for more than 600 seconds

mpsSysAlarmModuleStatusFailure

Set to 'critical' when a module that has been configured fails to reply with status

mpsSysAlarmNationalControlFault

Set to 'major' when there is no National Control stream present in an MPS configured for National Control

mpsSysAlarmNoCommandsWaiting

Set to 'warning' when no LOAD MPS commands are waiting to execute

mpsSysAlarmOutputOverflow

Set to 'critical' when there is an overflow of the buffers used to output packets when multiplexing

mpsSysAlarmServiceNotAuthorized

Set to 'major' when a service is not authorized but should be

mpsSysAlarmTemperatureFault

Set to 'major' when the temperature of the unit is out of spec

mpsSysAlarmWaitingForExtractedData

Set to 'major' when there are active Load MPS commands that are waiting for valid extracted data for more than one minute

mpsSysAlarmWatchdogReboot

Set to 'warning' when the last reboot was caused by a watchdog timeout

mpsSysAlarmZeroSystemTime

Set to 'warning' when the MPS System Time value is 0

mpsSysConfACPmode

Controls the current scrambling mode of the MPS ACPs

mpsSysConfInsertMode

Set the insertion mode for the MPS

mpsSysConfLoadMpsSource

Selects whether the MPS will be receiving Load MPS commands from local or national controller

mpsSysConfProductName

The product name of the MPS loaded at initialization from the config file

mpsSysConfSntpServerIP

The IP address of the specified SNTP server

mpsSysConfSntpServerSpecified

Specifies the TimeSource is SNTP

mpsSysConfTimeInputPort

The port of the input card from which the MPS should extract time when configured for receiving time from an input

mpsSysConfTimeInputSlot

The slot of the input card from which the MPS should extract time when configured for receiving time from an input

mpsSysConfTimeSource

The source for system time

mpsSysConfUDPcontrollerIP

The IP address of the local controller

mpsSysConfUDPcontrollerPort

The port of the local controller

mpsSysConfUDPmpsPort

The port of the MPS

mpsSysEventConfigurationError

Count of MPS configuration errors

mpsSysEventInputError

MPS input errors

mpsSysEventLoadMPSerror

Count of MPS load errors

mpsSysEventModuleStatusError

MPS status errors

mpsSysEventSIFinterfaceError

Count of SIF interface errors

mpsSysEventTimeProcessingError

Count of time processing errors

mpsSysEventUDPinterfaceError

Count of UDP interface errors

mpsSysLEDauthorized

This LED indicates whether the MPS has proper encryption and decryption authorization

mpsSysLEDconfigured

This LED indicates if the unit has been successfully configured

mpsSysLEDdcPowerOK

This LED indicates if the unit has good DC power

mpsSysLEDfaultSumm

This LED indicates if the unit has a current alarm greater than Major

mpsSysLEDinputFailure

This LED indicates if any modules have an input failure

mpsSysLEDoutputMuting

This LED indicates if any outputs are muted

mpsSysStatusCommandsActive

The value of this object is number of LOAD MPS commands currently active

mpsSysStatusCommandsWaiting

The number of LOAD MPS commands currently waiting to execute

mpsSysStatusPowerSupplyHwVersion

The power supply hardware version or MCN number

mpsSysStatusSysContBootCodeVersion

The System Controller boot code version

mpsSysStatusSysContHwVersion

The System Controller board hardware version or MCN number

mpsSysStatusSysContSifVersion

The System Controller board SIF PROM version or MCN number

mpsSysStatusSystemTime

The system time the MPS is using for commands and encryption purposes